E3D Revo™ Brass Nozzle, 0.8 mm

Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening, just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Experiment freely. With nozzle swapping this easy, you’re free to experiment with nozzle sizes you might not have used before. Set your 3D printer up for ultra-fine or ultra-thick extrusion widths in no time at all. Print large objects in less time or tiny objects with high resolution.  Frustration-free. Each Revo Nozzle is a preassembled nozzle and HeatBreak in one unit, so there’s no hazardous hot tightening and no chance of incorrect assembly. Say goodbye to frustrating HotEnd leaks and enjoy reliable 3D printing!  Rapid identification. Identify nozzle sizes at a glance, thanks to a colour-coded silicone sock. Plus, each Revo Nozzle has its size engraved into it with easy-to-read numbers, so there are no confusing identification markers to learn!  An expanding range. We’re ready to make RapidChange Nozzles in any size. Currently, we have brass nozzles in 0.15mm, 0.25mm, 0.4mm, 0.6mm and 0.8mm, with many more compatible nozzles to follow later. Wear-resistant and high-flow variants are already on our roadmap and will follow over time. Please note: Revo™ Nozzles are not compatible with V6-style heaterblocks You may need to adjust your Z offset when changing nozzles. Special care must be taken when using 0.15mm nozzles as these are more prone to jamming please see our recommended guidelines here

Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening, just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Experiment freely. With nozzle swapping this easy, you’re free to experiment with nozzle sizes you might not have used before. Set your 3D printer up for ultra-fine or ultra-thick extrusion widths in no time at all. Print large objects in less time or tiny objects with high resolution.  Frustration-free. Each Revo Nozzle is a preassembled nozzle and HeatBreak in one unit, so there’s no hazardous hot tightening and no chance of incorrect assembly. Say goodbye to frustrating HotEnd leaks and enjoy reliable 3D printing!  Rapid identification. Identify nozzle sizes at a glance, thanks to a colour-coded silicone sock. Plus, each Revo Nozzle has its size engraved into it with easy-to-read numbers, so there are no confusing identification markers to learn!  An expanding range. We’re ready to make RapidChange Nozzles in any size. Currently, we have brass nozzles in 0.15mm, 0.25mm, 0.4mm, 0.6mm and 0.8mm, with many more compatible nozzles to follow later. Wear-resistant and high-flow variants are already on our roadmap and will follow over time. Please note: Revo™ Nozzles are not compatible with V6-style heaterblocks You may need to adjust your Z offset when changing nozzles. Special care must be taken when using 0.15mm nozzles as these are more prone to jamming please see our recommended guidelines here

Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening, just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Experiment freely. With nozzle swapping this easy, you’re free to experiment with nozzle sizes you might not have used before. Set your 3D printer up for ultra-fine or ultra-thick extrusion widths in no time at all. Print large objects in less time or tiny objects with high resolution.  Frustration-free. Each Revo Nozzle is a preassembled nozzle and HeatBreak in one unit, so there’s no hazardous hot tightening and no chance of incorrect assembly. Say goodbye to frustrating HotEnd leaks and enjoy reliable 3D printing!  Rapid identification. Identify nozzle sizes at a glance, thanks to a colour-coded silicone sock. Plus, each Revo Nozzle has its size engraved into it with easy-to-read numbers, so there are no confusing identification markers to learn!  An expanding range. We’re ready to make RapidChange Nozzles in any size. Currently, we have brass nozzles in 0.15mm, 0.25mm, 0.4mm, 0.6mm and 0.8mm, with many more compatible nozzles to follow later. Wear-resistant and high-flow variants are already on our roadmap and will follow over time. Please note: Revo™ Nozzles are not compatible with V6-style heaterblocks You may need to adjust your Z offset when changing nozzles. Special care must be taken when using 0.15mm nozzles as these are more prone to jamming please see our recommended guidelines here

Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening, just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Experiment freely. With nozzle swapping this easy, you’re free to experiment with nozzle sizes you might not have used before. Set your 3D printer up for ultra-fine or ultra-thick extrusion widths in no time at all. Print large objects in less time or tiny objects with high resolution.  Frustration-free. Each Revo Nozzle is a preassembled nozzle and HeatBreak in one unit, so there’s no hazardous hot tightening and no chance of incorrect assembly. Say goodbye to frustrating HotEnd leaks and enjoy reliable 3D printing!  Rapid identification. Identify nozzle sizes at a glance, thanks to a colour-coded silicone sock. Plus, each Revo Nozzle has its size engraved into it with easy-to-read numbers, so there are no confusing identification markers to learn!  An expanding range. We’re ready to make RapidChange Nozzles in any size. Currently, we have brass nozzles in 0.15mm, 0.25mm, 0.4mm, 0.6mm and 0.8mm, with many more compatible nozzles to follow later. Wear-resistant and high-flow variants are already on our roadmap and will follow over time. Please note: Revo™ Nozzles are not compatible with V6-style heaterblocks You may need to adjust your Z offset when changing nozzles. Special care must be taken when using 0.15mm nozzles as these are more prone to jamming please see our recommended guidelines here

Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening, just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Experiment freely. With nozzle swapping this easy, you’re free to experiment with nozzle sizes you might not have used before. Set your 3D printer up for ultra-fine or ultra-thick extrusion widths in no time at all. Print large objects in less time or tiny objects with high resolution.  Frustration-free. Each Revo Nozzle is a preassembled nozzle and HeatBreak in one unit, so there’s no hazardous hot tightening and no chance of incorrect assembly. Say goodbye to frustrating HotEnd leaks and enjoy reliable 3D printing!  Rapid identification. Identify nozzle sizes at a glance, thanks to a colour-coded silicone sock. Plus, each Revo Nozzle has its size engraved into it with easy-to-read numbers, so there are no confusing identification markers to learn!  An expanding range. We’re ready to make RapidChange Nozzles in any size. Currently, we have brass nozzles in 0.15mm, 0.25mm, 0.4mm, 0.6mm and 0.8mm, with many more compatible nozzles to follow later. Wear-resistant and high-flow variants are already on our roadmap and will follow over time. Please note: Revo™ Nozzles are not compatible with V6-style heaterblocks You may need to adjust your Z offset when changing nozzles. Special care must be taken when using 0.15mm nozzles as these are more prone to jamming please see our recommended guidelines here

Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening – just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Experiment freely. With nozzle swapping this easy, you’re free to experiment with nozzle sizes you might not have used before. Set your 3D printer up for ultra-fine or ultra-thick extrusion widths in no time at all. Print large objects in less time, or tiny objects with high resolution.  Frustration-free. Each Revo Nozzle is a preassembled nozzle and heatbreak in one unit, so there’s no hazardous hot tightening and no chance of incorrect assembly. Say goodbye to frustrating HotEnd leaks and enjoy reliable 3D printing!  Rapid identification. Identify nozzle sizes at a glance thanks to a colour-coded silicone sock. Plus, each Revo Nozzle has its size engraved into it with easy-to-read numbers, so there are no confusing identification markers to learn!  An expanding range. We’re ready to make RapidChange Nozzles in any size. At launch, we’re introducing brass nozzles in 0.25mm, 0.40mm, 0.60mm and 0.80mm, with many more compatible nozzles to follow later. Wear-resistant and high flow variants are already on our roadmap and will follow over time. 

Swap your 3D printer’s nozzles in less than 60 seconds without tools or hot tightening – just use your fingers! If you can unscrew a tube of toothpaste, you can use a Revo Nozzle. Just screw one in to any Revo cold side and you’re ready to 3D print. Experiment freely. With nozzle swapping this easy, you’re free to experiment with nozzle sizes you might not have used before. Set your 3D printer up for ultra-fine or ultra-thick extrusion widths in no time at all. Print large objects in less time, or tiny objects with high resolution.  Frustration-free. Each Revo Nozzle is a preassembled nozzle and heatbreak in one unit, so there’s no hazardous hot tightening and no chance of incorrect assembly. Say goodbye to frustrating HotEnd leaks and enjoy reliable 3D printing!  Rapid identification. Identify nozzle sizes at a glance thanks to a colour-coded silicone sock. Plus, each Revo Nozzle has its size engraved into it with easy-to-read numbers, so there are no confusing identification markers to learn!  An expanding range. We’re ready to make RapidChange Nozzles in any size. At launch, we’re introducing brass nozzles in 0.25mm, 0.40mm, 0.60mm and 0.80mm, with many more compatible nozzles to follow later. Wear-resistant and high flow variants are already on our roadmap and will follow over time. 

E3D colour-coded silicone socks for Revo Nozzles. Never run out of silicone socks for your Revo 3D printing setup! This colour-coded sock kit includes ten silicone socks for all your 3D printing needs. The Revo Fully Loaded Sock Pack contains two socks for each Revo Nozzle size and an additional two for the Revo HeaterCore.

These retention springs clip onto your Revo HeaterCore on one side, before connecting to any Revo-compatible cold side on the other – including the Revo Micro, Revo Six, and Revo Hemera. The spring keeps the HeaterCore firmly attached to the cold side, while pushing it into the nozzle for improved thermal conductivity. Lost the spring for your Revo HeaterCore? Don’t worry, we sell spares! Keeps the HeaterCore into good thermal contact with a Revo Nozzle Effective in attaching Revo HeaterCore to heatsink  Compatible with Revo Micro, Revo Six, and Revo Hemera

E3D developed this Revo-compatible cold side in collaboration with Team Voron. It’s intended for use with the Voron StealthBurner, which includes an integrated cold side fan. It’s compatible with their Revo ecosystem, so you can change nozzle size without tools or hot tightening using just your fingers. Uses Revo Nozzles – change nozzles cold, no tools, no hot tightening Works with a Revo HeaterCore for faster heat-ups Rigid mounting using 4 x M3 x 0.5 bolts Ultra-lightweight construction for improved speed performance Ideal HotEnd for Voron StealthBurner Ready for Revo A groove at the bottom of the sink accepts a Revo HeaterCore spring. It’s compatible with our Revo ecosystem, so you can change nozzles without tools or hot tightening using just your fingers. Complements your Voron Includes an anodised red aluminium heatsink to complement your Voron accented parts. Rigid mounting This is a rigid mounted design that uses four M3 x 0.5 bolts to secure to your Voron 3D printer. Wire harness compatibility Please note that this is a custom production. The Thermistor and HeaterCore are wired to match our wire harness.

E3D developed this Revo-compatible HeatSink in collaboration with Team Voron. It’s intended for use with the Voron StealthBurner, which includes an integrated cold side fan. (Note: This means this kit will ship without a fan!) Uses Revo Nozzles (sold separately) – change nozzles cold, no tools, no hot tightening Works with a Revo HeaterCore (sold separately) for faster heat-ups Rigid mounting using 4 x M3 x 0.5 bolts Ultra-lightweight construction for improved speed performance Complements your Voron. This machined aluminium heatsink is anodised red to complement your Voron accented parts. Rigid mounting. Rigid mounted design that uses four M3 bolts to secure to your Voron 3D printer. Note Cold side fan not included. See https://docs.vorondesign.com/