Miniature ball bearings are deep groove ball bearings in small. Their dimensions make them suitable for special applications. In addition, they allow very high speeds with low noise.

Saw cut, precision milled and stress relieved cast aluminium plates. These are meant for DIY enthusiasts who want to create their own build plates. Made from the same raw material we use for our famous build plates!

Saw cut, precision milled and stress relieved cast aluminium plates. These are meant for DIY enthusiasts who want to create their own build plates. Made from the same raw material we use for our famous build plates!

Bondtech drive gear kit in hardened and surface protected steel. Precision cnc-machined. Super sharp teeths for maximum grip on the filament. The perfect choice for a high-performance feeding system. Extremely high wear resistance for use with abrasive filaments. These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 5 mm, secondary gear with two needle bearings, M3x2 setscrew and one 3x20 mm shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. Gear set for filament size 2.85 – 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.

Bondtech drive gear kit in hardened and surface protected steel. Precision cnc-machined. Super sharp teeths for maximum grip on the filament. The perfect choice for a high-performance feeding system. Extremely high wear resistance for use with abrasive filaments. These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 5 mm, secondary gear with two needle bearings, M3x2 setscrew and one 3x20 mm shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. Gear set for filament size 2.85 – 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.

Push Harder! Full Steel Ahead! Set of parts made of Hardened Steel to replace the plastic Drive and Main Double Gears on a Bondtech Large Gears eXtruder: LGX; LGX Lite; LGX Lite Mirrored. Recommended to feed Engineering grade thermoplastics. To use our LGX extruders above our default recommendations: with thicker mounting plates; at higher environment temperatures; at higher stepper motor currents. For detailed instructions (installation, usage, etc.) please follow official Bondtech instructions.

Spare part made of Hardened Steel to replace a Drive Wheel on a Bondtech LGX™ Large Gears eXtruder.

The Bondtech LGX® Large Gears eXtruder is the first of our filament feeders using Bondtech’s new Dual Drive Technology based on larger drive gears.

Includes full size LGX® Large Gears, maintenance windows and filament tension lever with 3 presets (open; rigid; flexible). Important Use the LGX® Lite only with a 36mm Round stepper motor featuring a 10 teeth motor gear. Stealthburner If you're looking for a really nice Stealthburner mount, checkout this mod: https://github.com/Eytecz/LGX_Lite_Stealthburner_CW2_style_mount/  

Spare part for the Bondtech LGX® Lite. Front housing made of grey Polyamide without dyeing. Features a wax protective coating and the LGX® Lite BONDTECH sticker.

The Bondtech LGX® Lite is a filament feeder based on the LGX® Large Gears eXtruder and uses Bondtech’s new Dual Drive Technology based on larger drive gears. Stealthburner If you're looking for a really nice Stealthburner mount, checkout this mod: https://github.com/Eytecz/LGX_Lite_Stealthburner_CW2_style_mount/

Spare part made of self lubricant high temperature plastic to replace a primary gear on a Bondtech LGX™ Large Gears eXtruder.

Spare part made of self lubricant high temperature plastic to replace a secondary gear on a Bondtech LGX™ Large Gears eXtruder.

Push-fit ECAS 4mm is a Bondtech Spare Part to use on the BMG Extruder and on the DDS for CR-10S when a replacement is needed. Size 4 mm is used with 1.75 mm filament.

Replacement Shaft assembly for our Bondtech Mini Geared (BMG), SingleDirect and DualDirect extruders. It includes the set screw for primary 1.75/5.0 drive gear.Note: New improved revision from Bondtech, where the gear wheel is in white now! For more information see link

Thumbscrew replacement for Bondtech extruder.

Brass heat inserts, specially developed for FDM 3D printed parts and post-insertion.

Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.

Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.

Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.

Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.

Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.

Genuine CPC miniature linear guideway; single rail cut to length with a single long block. Highest preload (V1) and normal (N) precision guarantees a stiff / play-free and binding-free motion. The blocks feature an injection hole for lubrication. Warranty The blocks and rails are non-interchangeable - keep the blocks on the rails! A violation does expire warranty effectively. Cleaning We strongly recommend to clean the rails before lubrication. Put a zip tie through the very last holes to ensure the block can not escape the rail. Fill a glass with some grease solvent and soak the blocks for at least an hour. Rinse the blocks and wipe the rail from any residue grease with a lint-free cloth. Lubrication We recommend to lubricate the ball races and bearing balls with grease, and cover the entire rail itself in a thin coat of grease to prevent oxidation. Recommended lubricants (in no particular order): CPC Lubrication Kit 18G Fuchs Planto Multispray S Fuchs Lagermeister BF2 Mobilux EP 1 or EP 2 HIWIN G05 Note: lubricants containing MoS2 or graphite must not be used.