Standard: UL 248-14(M) Medium time-lagCylindrical, 5 x 20 mm125 V / 250 V Voltage

Standard: UL 248-14(M) Medium time-lagCylindrical, 5 x 20 mm125 V / 250 V Voltage

The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C

The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C

The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C

The silicone heatmats were custom designed by Fermio Labs and made to spec by Keenovo. All heaters are optimized for our build plates shapes and hole positions. They allow even heating almost all the way to the edges of the build plate. The power is adjusted to allow running them at 100 % power without risking damage to the build plate instead of the 50% to 80% PWM limit recommended for the heaters listed on the BOM. The standard DIN466 thumb nuts used in all Voron printers used as spacers (VORON2) or levelling nuts (Trident, VORON0 and VORON1) can be used as guides to align the heater. For added safety all heaters come with a self resetting bi-metal 150C thermostat. This turns off the heater if temperatures reaches 150 C due to technical failure of your electronics (only meant as a safety feature, not for temperature regulation). Thermistor used is a NTC 100K thermistor (Beta 25/50 3950K-1%, click here for the R-T datasheet) Choose type 11 or 13 in Marlin firmware. Use "Generic 3950" in Klipper. SKU/Model Compatibility Dimensions Voltage Watt Ampere Thermostat FLG-VRN-KNV-110 VORON0 110 x 110 mm 24 V/DC 60 W 2.5 A 150° C FLG-VRN-KNV-240 250 Trident, VORON1, VORON2 240 x 240 mm 230 V/AC 300 W 1.3 A 150° C FLG-VRN-KNV-290 300 Trident, VORON1, VORON2 290 x 290 mm 230 V/AC 400 W 1.7 A 150° C FLG-VRN-KNV-340 350 Trident, VORON2 340 x 340 mm 230 V/AC 500 W 2.1 A 150° C

Suitable for Pocketwatch 1 extruder.

Weight: 20gModular Keystone Inline Coupler 6 Class E 250 MHzISO/IEC 11801 and TIA/EIA 568B.2-12x RJ45 jack, fully unshieldedSnap-in mountingPin configuration: 1:1

Snap-in Keystone Modulesuitable for standard keystone panels and outletsConnections: USB-A female to USB-A femaleApplication: USB 3.0 cablingMaterial: Nickel-plated contact, thermoplastic housingDimension: 35 x 14,5 x 16,7 mmColor: Black

Endstop Microswitch usable for X/Y/Z. Type: D2F-5LRating: 250 V/AC - 5A

Genuine OMRON TL-Q5MC2 2M NPN NC inductive sensor, suitable as Z probe, with a 5mm sensing distance. Note does not sense Aluminium early enough. Requires a spring steel sheet needs longer screws than the BOM sensor (2x M3x25 instead of M3x20)

Number of poles: 2 + PEContinuous current: 10AFuse holder: 6.3APin temperature: 70°CRated voltage: 250V ACWith rocker switch and fuse holderCombination consists of appliance plug, 2-pole rocker switch and fuse holder for fuse link(5x20mm)Connection by flat cable plug 4.8mmSnap-in assembly

This solid state relay can switch load currents in the range of 24-480VAC (usually 230V) up to currents of 10A. zero cross switching galvanic isolation (opto-isolator) touch protection (IP20) switching state signaling with LED Downloads A-Senco SSR-500-1DA48-10 Datasheet

Adapter plate for mounting our SSR to our DIN rails.

StealthBurner RGB LED Kit, pre-wired. Total of three SK6812 RGBNW LEDs. Wire terminated with 3-pin Molex Microfit 3.0 connector. Hint Use our prepared connection cable StealthBurner RGB LED Wire Harness to update your wire harness. Note The M42 hexnut and 3D printed parts are not part of this kit and are pictured for demonstration purposes only.

Wire harness addition for our StealthBurner RGB LED Kit using black Helukabel Heluflon®-fep-6y 0.25mm². One end with a Molex MicroFix 3.0 connector, the other end with a Dupont connector fitting for BTT Octopus and Fysetc Spider.

Wire harness addition for our StealthBurner RGB LED Kit using black Helukabel Heluflon®-fep-6y 0.25mm². One end with a Molex MicroFix 3.0 connector, the other end with a Dupont connector fitting for BTT Octopus and Fysetc Spider.

Wire harness addition for our StealthBurner RGB LED Kit using black Helukabel Heluflon®-fep-6y 0.25mm². One end with a Molex MicroFix 3.0 connector, the other end with a Dupont connector fitting for BTT Octopus and Fysetc Spider.

The SUNON MF50151VX-B00U-A99 is suitable for Nevermore Micro V4 and V5 Duo. Note The fan comes without any connectors, just bare wires. Contents 1 pcs of SUNON MF50151VX-B00U-A99

DIY Z Endstop PCB, requires custom printed part and soldering. Contents 1x PCB 1x 3-Pin JST-XH connector 1x Omron D2F-5L Hint Use our prepared connection cable Nozzle Endstop Wire Harness Downloads Z-Switch_FermioLabs_Rev1.stl Note Pins of the connector and microswitch have to be cutted very flat before soldering!

Wire harness for our Nozzle Endstop with 100cm of black Helukabel Heluflon®-fep-6y 0.25mm² and on both ends you have a already crimped 3-pin JST-XH connector.

X/Y Hall Effect Endstop for contactless end position triggering. The Endstop is plug&play for our Wire Harness! Contents 1x Hall Effect Endstop, ready and 100% tested 2x 6x3mm black magnets Note: For using it, you need a different print part from the release ([a]_endstop_pod_hall_effect.stl)

DIY X/Y Microswitch Endstop PCB. This PCB is compatible with our Wire Harness! Soldering and printed part required. Contents 1x PCB 1x 4-Pin black JST-XH compatible connector Note: you need two Omron D2F-5L or similar microswitches! Download Microswitch_Edge_Pod.stl

Note #1: the wire harness is compatible with VORON Trident and VORON1 V1.8, but marketed as VORON2 V2.4 wire harness. Note #2: For the BTT Octopus you can, optionally / as a fallback, use the SKR wire harness. All required JST-XH connectors are included to do the minor modifications. See our adjustment guide for a conversion. Note #3: The LED wires for StealthBurner are not included and have to be bought separately. Are you still crimping or already printing? If you hate bad crimps and realizing how bad your eye sight really is, we have a solution! We're happy to announce that we're the first source worldwide ever for a ready made drop in wire harness using only the highest quality components available: Drop in ready wire harness for VORON2 V2.4 using 2x BTT SKR 1.3/1.4, 1x BTT Octopus or 1x FYSETC Spider MCUs (one JST connector change required for SKR 1.3) Wire harness 100% made in Germany by a well known wire harness manufacturer. All wires are black Helukabel Heluflon®-fep-6y 0.5mm² for the hotend heater and 0.25 mm² for everything else. Some even call these wires the mother of all cables! Only geniune JST and Molex connectors, crimped with professional dies on semi automatic industrial machines. To keep it black, without distracting white labels, all connectors are directly printed with the function. Black is the new orange! Black/red color coding on both ends for all V+ and V- wires. SKR-Variant: BAT85 Diode already included into the probe signal wire. A and B motor connectors for most common motors with detatchable wires and JST-PH 6 pin connectors X/Y-Endstop prepared for 4 pin JST-XH connector. We recommend our compatible Hall Endstop board or the Microswitch PCB, both with JST-XH connector. All wires at the X carriage terminated with Molex Microfit 3.0 connectors (yes, they fit below the stock cable cover) Sufficient wire length for proper wire management under the skirt.