Bondtech drive gear kit in hardened and surface protected steel. Precision cnc-machined. Super sharp teeths for maximum grip on the filament. The perfect choice for a high-performance feeding system. Extremely high wear resistance for use with abrasive filaments. These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 5 mm, secondary gear with two needle bearings, M3x2 setscrew and one 3x20 mm shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. Gear set for filament size 2.85 – 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.

Bondtech drive gear kit in hardened and surface protected steel. Precision cnc-machined. Super sharp teeths for maximum grip on the filament. The perfect choice for a high-performance feeding system. Extremely high wear resistance for use with abrasive filaments. These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 5 mm, secondary gear with two needle bearings, M3x2 setscrew and one 3x20 mm shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. Gear set for filament size 2.85 – 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.

Push Harder! Full Steel Ahead! Set of parts made of Hardened Steel to replace the plastic Drive and Main Double Gears on a Bondtech Large Gears eXtruder: LGX; LGX Lite; LGX Lite Mirrored. Recommended to feed Engineering grade thermoplastics. To use our LGX extruders above our default recommendations: with thicker mounting plates; at higher environment temperatures; at higher stepper motor currents. For detailed instructions (installation, usage, etc.) please follow official Bondtech instructions.

Spare part made of Hardened Steel to replace a Drive Wheel on a Bondtech LGX™ Large Gears eXtruder.

The Bondtech LGX® Large Gears eXtruder is the first of our filament feeders using Bondtech’s new Dual Drive Technology based on larger drive gears.

Includes full size LGX® Large Gears, maintenance windows and filament tension lever with 3 presets (open; rigid; flexible). Important Use the LGX® Lite only with a 36mm Round stepper motor featuring a 10 teeth motor gear. Stealthburner If you're looking for a really nice Stealthburner mount, checkout this mod: https://github.com/Eytecz/LGX_Lite_Stealthburner_CW2_style_mount/  

Spare part for the Bondtech LGX® Lite. Front housing made of grey Polyamide without dyeing. Features a wax protective coating and the LGX® Lite BONDTECH sticker.

The Bondtech LGX® Lite is a filament feeder based on the LGX® Large Gears eXtruder and uses Bondtech’s new Dual Drive Technology based on larger drive gears. Stealthburner If you're looking for a really nice Stealthburner mount, checkout this mod: https://github.com/Eytecz/LGX_Lite_Stealthburner_CW2_style_mount/

Spare part made of self lubricant high temperature plastic to replace a primary gear on a Bondtech LGX™ Large Gears eXtruder.

Spare part made of self lubricant high temperature plastic to replace a secondary gear on a Bondtech LGX™ Large Gears eXtruder.

Push-fit ECAS 4mm is a Bondtech Spare Part to use on the BMG Extruder and on the DDS for CR-10S when a replacement is needed. Size 4 mm is used with 1.75 mm filament.

Replacement Shaft assembly for our Bondtech Mini Geared (BMG), SingleDirect and DualDirect extruders. It includes the set screw for primary 1.75/5.0 drive gear.Note: New improved revision from Bondtech, where the gear wheel is in white now! For more information see link

Thumbscrew replacement for Bondtech extruder.

E3D colour-coded silicone socks for Revo Nozzles. Never run out of silicone socks for your Revo 3D printing setup! This colour-coded sock kit includes ten silicone socks for all your 3D printing needs. The Revo Fully Loaded Sock Pack contains two socks for each Revo Nozzle size and an additional two for the Revo HeaterCore.

These retention springs clip onto your Revo HeaterCore on one side, before connecting to any Revo-compatible cold side on the other – including the Revo Micro, Revo Six, and Revo Hemera. The spring keeps the HeaterCore firmly attached to the cold side, while pushing it into the nozzle for improved thermal conductivity. Lost the spring for your Revo HeaterCore? Don’t worry, we sell spares! Keeps the HeaterCore into good thermal contact with a Revo Nozzle Effective in attaching Revo HeaterCore to heatsink  Compatible with Revo Micro, Revo Six, and Revo Hemera

E3D developed this Revo-compatible cold side in collaboration with Team Voron. It’s intended for use with the Voron StealthBurner, which includes an integrated cold side fan. It’s compatible with their Revo ecosystem, so you can change nozzle size without tools or hot tightening using just your fingers. Uses Revo Nozzles – change nozzles cold, no tools, no hot tightening Works with a Revo HeaterCore for faster heat-ups Rigid mounting using 4 x M3 x 0.5 bolts Ultra-lightweight construction for improved speed performance Ideal HotEnd for Voron StealthBurner Ready for Revo A groove at the bottom of the sink accepts a Revo HeaterCore spring. It’s compatible with our Revo ecosystem, so you can change nozzles without tools or hot tightening using just your fingers. Complements your Voron Includes an anodised red aluminium heatsink to complement your Voron accented parts. Rigid mounting This is a rigid mounted design that uses four M3 x 0.5 bolts to secure to your Voron 3D printer. Wire harness compatibility Please note that this is a custom production. The Thermistor and HeaterCore are wired to match our wire harness.

E3D developed this Revo-compatible HeatSink in collaboration with Team Voron. It’s intended for use with the Voron StealthBurner, which includes an integrated cold side fan. (Note: This means this kit will ship without a fan!) Uses Revo Nozzles (sold separately) – change nozzles cold, no tools, no hot tightening Works with a Revo HeaterCore (sold separately) for faster heat-ups Rigid mounting using 4 x M3 x 0.5 bolts Ultra-lightweight construction for improved speed performance Complements your Voron. This machined aluminium heatsink is anodised red to complement your Voron accented parts. Rigid mounting. Rigid mounted design that uses four M3 bolts to secure to your Voron 3D printer. Note Cold side fan not included. See https://docs.vorondesign.com/