StealthBurner RGB LED Wire Harness, 300 Spec

Bondtech drive gear kit in hardened and surface protected steel. Precision cnc-machined. Super sharp teeths for maximum grip on the filament. The perfect choice for a high-performance feeding system. Extremely high wear resistance for use with abrasive filaments. These drivegear kits come as a set consisting of a primary drive gear, a secondary drive gear, bearings and a shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 5 mm, secondary gear with two needle bearings, M3x2 setscrew and one 3x20 mm shaft. Gear set for filament size 1.75 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. Gear set for filament size 2.85 – 3.0 mm, primary gear with inner diameter 8 mm, secondary gear with integrated needle bearings, M4x3 setscrew and one 4x22 mm shaft. A Lithium based grease is recommended to use on the gear section and inside the needle bearings for low friction and to avoid wear. A small dab of grease is enough.

Replacement Shaft assembly for our Bondtech Mini Geared (BMG), SingleDirect and DualDirect extruders. It includes the set screw for primary 1.75/5.0 drive gear.Note: New improved revision from Bondtech, where the gear wheel is in white now! For more information see link

Thumbscrew replacement for Bondtech extruder.

Brass heat inserts, specially developed for FDM 3D printed parts and post-insertion.

E3D developed this Revo-compatible cold side in collaboration with Team Voron. It’s intended for use with the Voron StealthBurner, which includes an integrated cold side fan. It’s compatible with their Revo ecosystem, so you can change nozzle size without tools or hot tightening using just your fingers. Uses Revo Nozzles – change nozzles cold, no tools, no hot tightening Works with a Revo HeaterCore for faster heat-ups Rigid mounting using 4 x M3 x 0.5 bolts Ultra-lightweight construction for improved speed performance Ideal HotEnd for Voron StealthBurner Ready for Revo A groove at the bottom of the sink accepts a Revo HeaterCore spring. It’s compatible with our Revo ecosystem, so you can change nozzles without tools or hot tightening using just your fingers. Complements your Voron Includes an anodised red aluminium heatsink to complement your Voron accented parts. Rigid mounting This is a rigid mounted design that uses four M3 x 0.5 bolts to secure to your Voron 3D printer. Wire harness compatibility Please note that this is a custom production. The Thermistor and HeaterCore are wired to match our wire harness.

Miniature ball bearings are deep groove ball bearings in small. Their dimensions make them suitable for special applications. In addition, they allow very high speeds with low noise.

Front and back of the Stealthburner Clockwork2 E3D Revo Voron toolhead mount. Note You are buying 3D printed parts only. Any additional hardware shown is for demonstration purposes only.

Stealthburner Clockwork2 compatible Bondtech LGX Lite mount with igus energy chain mount. Note You are buying 3D printed parts only. Any additional hardware shown is for demonstration purposes only.

StealthBurner RGB LED Kit, pre-wired. Total of three SK6812 RGBNW LEDs. Wire terminated with 3-pin Molex Microfit 3.0 connector. Hint Use our prepared connection cable StealthBurner RGB LED Wire Harness to update your wire harness. Note The M42 hexnut and 3D printed parts are not part of this kit and are pictured for demonstration purposes only.

Wire harness addition for our StealthBurner RGB LED Kit using black Helukabel Heluflon®-fep-6y 0.25mm². One end with a Molex MicroFix 3.0 connector, the other end with a Dupont connector fitting for BTT Octopus and Fysetc Spider.

Wire harness addition for our StealthBurner RGB LED Kit using black Helukabel Heluflon®-fep-6y 0.25mm². One end with a Molex MicroFix 3.0 connector, the other end with a Dupont connector fitting for BTT Octopus and Fysetc Spider.

Wire harness addition for our StealthBurner RGB LED Kit using black Helukabel Heluflon®-fep-6y 0.25mm². One end with a Molex MicroFix 3.0 connector, the other end with a Dupont connector fitting for BTT Octopus and Fysetc Spider.

The SUNON MF50151VX-B00U-A99 is suitable for Nevermore Micro V4 and V5 Duo. Note The fan comes without any connectors, just bare wires. Contents 1 pcs of SUNON MF50151VX-B00U-A99